Washing machine repairs Dandenong

Washing machine repairs Dandenong

Does your washing machine repairs Dandenong not spin and also make a noise? Typically, this problem is a bad motor coupler. It’s, a two-dollar piece: it’s, really easy to fix. I’m gonna show. You how to fix it today, I’m gonna be working on a Kenmore, but this also applies to the whirlpool, and pretty much any washer is going to be the same process.

What we’re gonna do is we’re gonna go underneath there’s? No need to take off any panels or anything you go right underneath it.

So I’m gonna pull this out and then tilt it upwards. So here all the tools you’re gonna need, you might not need the rubber mallet. It depends on how hard your coupler is to get on. I’ll. Show you all that later on, you got your part.

Using that’s, the part number flat-head screwdriver and a ratchet with a one-quarter-inch socket. Let’s begin. So all we’re gonna do. Is we’re going to tilt this? I’m gonna use a jack stand just to keep it tilted, make sure you unplug, the electricity for the washer machine might also consider shutting off the water to the hot in the cold water.

We’re, not going to do anything with the hot and cold water, but just to be safe, so you don’t spring a leak or something so now with it unplugged we’ll go underneath you can see. This is the pump. This right here is the motor and then between the motor and the transmission is the coupler and what you’re gonna do.

Is you’re, just gonna spin it by hand? In this case, I don’t? Really have to spin it very far. You can see right there, it’s, broken it’s designed to break so you don’t damage your motor. You no damage the transmission.

If there’s too much of a load, they also break because they get old and brittle it’s a $ 2.00 part. It’s a five-minute job. Let me show you how to replace it now that we identified that’s, the problem.

This is the first thing we’re, going to take off it’s, really simple Washing machine repairs Dandenong. There’s, two metal Clips there’s, one here that pops off like that, and then there’s, one up here, just pops off with a finger. Then you just wiggle this loose and move it off to the side.

You can see that there’s some dust around here, and I recommend that you vacuumed that out so the same process that we took off this pump here. With these clips, we’re gonna have to take off these clips that hold in the motor there’s.

One down washing machine repairs Dandenong here and there’s one up here and then this is a quarter. Inch socket loosens it up. Let’s. One get this top one up here. That’s. Two now that these two are unscrewed, we’re, just getting a flathead screwdriver and we’re going to just pop each clip out got the bottom one out do the same thing for the top clip.

Now your motor is free to get pulled out, it’s, heavy, be careful and just set that down, so the motor is out and you can see it couples right in there and we look here. This is the piece that’s. Broken so just take it off, and then that’ll come right out, so you could take this.

This is garbage. If you want, you could keep the one that is intact just in case, you want an extra part if it breaks and you could fix it on the fly. While you get your parts ordered since this is still good.

I’m, replacing everything, but in my case, this piece is still good and this piece is still good, so I’m gonna keep it for spare parts. This is the piece that broke and that’s. Why? You heard all that clanking and clicking so here’s, the nice new one.

All it does is slide right on here. It only fits in one way: it doesn’t matter which side you use so just slide that on there should be a pretty tight, fit good. And then, when you look on here, there’s, no space for it to slide in anymore, so to make it easier for yourself just take out this plastic piece here on the coupler that comes out make sure the black piece is seated all the Way just press down on it and we’re gonna take this, I’m gonna go in here.

We’re gonna push this on, so just press this all the way down. Okay with that pushed all the way in, we could connect the motor if this is hard to push in or if this is hard to push in, you could use a rubber, mallet and just lightly tap it.

Don’t, go crazy. You don’t want to break this, but that little extra tapping really does help push this in. It is a pretty tight fit. So this is pushed all the way in when this is basically flush and if you look at the side view there’s, no extra space to push this in so that’s.

How you know it’s all the way in to make this easy align it. So the top peg is at the 12 o’clock position, and these two pegs are at the bottom and we’re gonna. Do the same here, the hole for the top peg will be at the 12 o’clock position, and that should allow us to slide this in really easily one of our metal Clips did pop out before so.

To put that in all, you do is find that slot in there and after you find the slot, stick it in and turn it and that’s in so don’t worry. If these things pop out now, we’re gonna get our motor to remember.

It goes in just like this. That white piece is on the bottom here, and the wiring harness is on the side. You’re gonna have to use it both hands because it is pretty heavy and just turn the motor a little bit to get it in place and wiggle it, and there we go just locked into place.

So now that our motors in we have this clip here – and we have a clip up here – so we’re gonna – do the top first cuz it’s, a lot easier. You just tilt the motor back like that. That’ll clip in now. We let go the motor and then now the bottom one will go in a lot easier.

It’s, a lot easier to do the top first in the bottom. Second good now the motor is locked in. Remember we have these two screws that need to go in tighten the bottom one. First, it doesn’t really matter at this point.

Just tighten them both down you, don’t have to go super tight, just snug them up. That’s perfect. We got that second one up here and just snug it down. Just like that again, don’t make these super tight.

Then the last thing we have to do is we have to slide this onto that piece. Right there, you might have to align it. Well, see if this just fits on, give it a little twist off there. You go it actually wasn’t lined if it’s not aligned just twist it a little bit to get it aligned.

That goes in like that. Now, these clips fell out before, and putting them in will be the same as the other clips. It’s, just a t-shaped piece that you push in and then twists. So you just find the hole here, push it in twist it, and then this will snap onto here just like so and the same thing for the back one.

You know just feel around for the hole holes right there put it in a twist it and get that on everything’s locked in just gives it a little shake to make sure it feels solid. Everything should feel solid.

Now I can remove our jack stand slowly tilt this down, and now we’re gonna give it a shot to see if it works. Okay, now we’ll plug it back in we’ll test it out see if it works. Also, don’t forget if you shut these off turning them back on and it works.

So now you can just push the washer back and you’re good to go and that’s. How you replace a motor coupler on your washing machine cost. You two bucks, nice and easy to do, takes ten minutes max the top tip for this video.

Are you see this one right here this hose? That goes all the way down that’s. Your water exhaust hose that’s where the water drains after you’re done washing. Make sure that you do not pull the washing machine out too far, because if you do that happens and then water starts shooting out.

As you can tell that’s, what happened to me keep an eye on this don’t. Let there be too much tension on this. Otherwise, water will get all over your floor and just to make sure that that problem, doesn’t happen again.

Don’t let it pull out too far, but also you can use the pliers and make sure that the hose is pushed all the way down, and this clamp is on there. Good

Washing Machine Repairs Ringwood

Washing Machine Repairs Ringwood

If your Washing Machine Repairs Ringwood fills with water however doesn’t agitate or spin, you may have to re set your washer. Even the Hydrowave washer has a direct-drive system. This system doesn’t want a transmission to agitate or twist.

So the motor takes to a larger part in the drive .

This mistake code may shut down the driveway. The drive system might be fine, you being a consumer may refresh the motor. No equipment will be required. You should follow these 3 simple actions.

  1. electricity farther down the machine by stretching the washer against the socket.
  2. wait around 1 minute plus plug at the washer back in the outlet.
  3. you finally have thirty minutes after the unit is motivated to elevate and then reduce the lid six times.

After you begin lifting and lifting the lid, then then you want to complete the cycle six times over 1-2 seconds.

As a way to carry out this action correctly, look at the bottom of one’s lid and you will find a magnet in front right corner. Subsequent to the lid has been shut, this magnet strikes the lid button that’s just below the small vinyl rectangle that the magnet rests on in the closed place.
On a few, but maybe not all designs, you can notice the lid switch clicking as you raise and lower the lid. No matter your version and whether you listen to this snapping sound, you should remember to completely shut the lid just as instructed.

You only have to raise the lid inches to carve your own connection. Your motor is reset. Start with running a tiny load without even putting garments in your machine. In the event the machine warms and commences, you can set your clothes inside and finish the clean cycle.

If the device doesn’t agitate or should after a few heaps of clothes your washer ceases, remember to telephone to get assistance: 1-800-GE-CARES. If your washer dryer fills with water but does not agitate or twist you may Want to reset your washer washer The Hide-away washer is equipped with an Immediate drive system that this machine doesn’t Call for a transmission to agitate or spin hence the engine takes on a bigger Part in the push system in the Event Your washer believes something uncommon for example an Electric spike an unbalanced load along with a disruption in power it might ship an error code to a engine this fault code might shut down the drive system the driveway system might well be fine you personally since a user can reset the motor without any tools have been required Remember to follow these 3 easy measures 1 power down the device by clipping the washer contrary to the socket to wait for approximately 1 minute and plug at the washer Back to the outlet a Few you eventually have Thirty minutes after the device is powered to lift and reduce the lid twice the Moment you get started lifting and lowering the lid you need to End the cycle 6 times More than 12 minutes as a Way to Conduct This action properly look at the Bottom of One’s lid and you will notice a magnet at front right corner when the lid has been closed this magnet strikes the lid that’s just beneath the Modest plastic rectangle that the magnet rests in the closed place on some although maybe not all versions that you will hear the lid button tapping because you raise and lower the lid No Matter One’s variant and whether you hear the clicking noise just be certain to fully shut the lid as instructed you Just Have to lift the lid two inches to divide this connection your motor is now reset begin by running a Little load without even putting clothes in the device in the Event the System fills and begins you May Set Your Clothing inside and complete the wash cycle when the Machine does not urge or when following several heaps of clothes your washer ceases again call for support you 800 GE fails

washing machine repair

Washing Machine Repair

This article discusses the Washing Machine Repair functions. We mean to assist you with diagnosing issues to and help you when making an appointment with Neil Maurice Appliances.

Above all else, we’re, going to eliminate the cover of the Washing Machine Repair. At times the screws are on the back. Be that as it may, on this one they’re on the sides. When the top eliminated, we’re above all else, going to investigate where the water enters the machine, and this is the water channel valves.

This is the place your channel hoses are associated with. In case you’re having an issue and your machine, isn’t topping off the valves could be to blame. Most importantly, however, check your hoses aren’t crimped and check your water.

S turned on the water will at that point enter your allocator cabinet by means of the container lodging, where your texture, conditioner, and cleanser is. We and # 39. Ve got a great deal of clients grumbling to us that their texture, conditioner, or cleanser isn’t being taken into the machine, and the most concerning issue is that the distributor lodging is really obstructed.

In the event that we take out the gadget cabinet and, at that point we can investigate the distributor lodging itself from inside and as you’ll see by this one, there’s, a great deal of dark shape and gunge that is hindering the gaps.

So water can’t deplete into the container cabinet and remove that cleanser and cleanser. On the off chance that this is a difficulty that you’re confronting, at that point you have to clean altogether a distributor lodging from inside or on the off chance that that comes up short, at that point basically supplant it and now fix the issue.

Next, we’re, going to eliminate the front board. The front board on this Hotpoint leaves away. Above all else, we have to eliminate the belt board, however, whenever this is taken out, we can eliminate the kick strip, which is at the lower part of the machine, which at that point picks up that admittance to the screws for the front board.

At the base, next, we have to eliminate the forward portion of the entryway seal. This is done basically by prising the way, entryway seal retainer with a level bladed screwdriver. As should be obvious, this leaves away decent and effectively ensure you spare the wire retainer for when we refit the entryway seal toward the end, the entryway seal, at that point basically strips back prepared for the front board to be eliminated.

Be that as it may, above all else, we have to eliminate the entryway interlock. This is held set up by a few screws on the front board. The entryway interlock is a security component that guarantees the machine will possibly work when the entryway is shut.

Presently, on the off chance that you and # 39, ve got a broken entryway. Interlock. The side effects will be that your machine will show up dead once the entryway interlocks eliminated and the entryway seal front is taken out. We would then be able to eliminate the screws that are hanging on the head of the entryway board.

Presently the entryway board will essentially lift away returning to water entering the machine. Water enters the machine rather gadget to top hose. It will just arrive at a specific level which is controlled by the Washing Machine Repairs pressure framework.

The weight framework is comprised of a weight chamber pressure hose and a weight switch. In the event that your machine is overloading, at that point this could be the territory for concern, give specific consideration to the weight chamber for blockages and the hose for any gaps.

Clearly, a Washing Machine Repair is defenseless to spills, and these can be from all transitory aspect of the Washing Machine Repair, including the tub itself. Next, the water will start to warm up. This is finished by the radiator component which will be found at the lower part of the machine.

In the event that yours is flawed, at that point your water won’t heat up. This is constrained by the indoor regulator, which could likewise be the reason for the issue. When the warmer component has been turned on, the wash cycle will start and your drum will turn in reverse and advances upsetting the garments.

Presently, on the off chance that your machine neglects to do this, at that point there’s, an issue and it lies typically with either the belt or most pessimistic scenario. The engine itself. Try not to speculate the engine straight away and it’s probably going to be the carbon brushes if the belt is as yet flawless.

Easy Washing Machine Repair

When the machine has completed the cycle, it will at that point siphon the water out. This again will be found at the lower part of the machine. So in the event that your machine is a discharging, at that point this is the imaginable course consistently check for blockages.

To begin with, at that point, the last part I need to specify is the control, module or clock the minds behind the machine, however something turns out badly. Individuals frequently expect this is the place the deficiency will lie. Nonetheless, usually, the flaw really lies with one of the segments we’ve just referenced.

Indeed, much obliged for watching the machine we’ve been showing on is a Hotpoint Washing Machine Repair. On the off chance that yours is another brand, at that point it may be somewhat unique. In any case, the segments will all be fundamentally the same as.